Anchor: #BGBIGGHA

Section 4: Pavement Types

Anchor: #i1008954

Flexible Pavement

A flexible pavement structure is typically composed of several layers of material with better quality materials on top where the intensity of stress from traffic loads is high and lower quality materials at the bottom where the stress intensity is low. Flexible pavements can be analyzed as a multilayer system under loading.

A typical flexible pavement structure consists of the surface course and underlying base and subbase courses. Each of these layers contributes to structural support and drainage.

When hot mix asphalt (HMA) is used as the surface course, it is the stiffest (as measured by resilient modulus) and may contribute the most (depending upon thickness) to pavement strength. The underlying layers are less stiff but are still important to pavement strength as well as drainage and frost protection.

When a seal coat is used as the surface course, the base generally is the layer that contributes most to the structural stiffness. A typical structural design results in a series of layers that gradually decrease in material quality with depth. Figure 2-1 shows a typical section for a flexible pavement.

Typical section for a flexible pavement. (click in image to see full-size image) Anchor: #BGBIBHJAgrtop

Figure 2-1. Typical section for a flexible pavement.

Anchor: #i1064480

Perpetual Pavement

Perpetual pavement is a term used to describe a long-life structural design. It uses premium HMA mixtures, appropriate construction techniques and occasional maintenance to renew the surface. Close attention must be paid to proper construction techniques to avoid problems with permeability, trapping moisture, segregation with depth, and variability of density with depth. A perpetual pavement can last 30 yr. or more if properly maintained.

Structural deterioration typically occurs due to either classical bottom-up fatigue cracking, rutting of the HMA layers, or rutting of the subgrade. Perpetual pavement is designed to withstand almost infinite number of axle loads without structural deterioration by limiting the level of load-induced strain at the bottom of the HMA layers and top of the subgrade and using deformation resistant HMA mixtures. Figure 2-2 shows a generalized perpetual pavement design. Detailed construction considerations are available through this link.

Generalized perpetual pavement design. (click in image to see full-size image) Anchor: #BGBJIGJBgrtop

Figure 2-2. Generalized perpetual pavement design.

Anchor: #i1009010

Rigid Pavement

A rigid pavement structure is composed of a hydraulic cement concrete surface course and underlying base and subbase courses (if used). Another term commonly used is Portland cement concrete (PCC) pavement, although with today’s pozzolanic additives, cements may no longer be technically classified as “Portland.”

The surface course (concrete slab) is the stiffest layer and provides the majority of strength. The base or subbase layers are orders of magnitude less stiff than the PCC surface but still make important contributions to pavement drainage and frost protection and provide a working platform for construction equipment.

Rigid pavements are substantially ‘stiffer’ than flexible pavements due to the high modulus of elasticity of the PCC material, resulting in very low deflections under loading. The rigid pavements can be analyzed by the plate theory. Rigid pavements can have reinforcing steel, which is generally used to handle thermal stresses to reduce or eliminate joints and maintain tight crack widths. Figure 2-3 shows a typical section for a rigid pavement.

Typical section for a rigid pavement. (click in image to see full-size image) Anchor: #BGBGAIFAgrtop

Figure 2-3. Typical section for a rigid pavement.

Anchor: #i1064631

Continuously Reinforced Concrete Pavement

CRCP provides joint-free design. The formation of transverse cracks at relatively close intervals is a distinctive characteristic of CRCP. These cracks are held tightly by the reinforcement and should be of no concern as long as the cracks are uniformly spaced, do not spall excessively, and a uniform non-erosive base is provided. Figure 2-4. shows a typical section of CRCP.

Continuously Reinforced Concrete Pavement. (click in image to see full-size image) Anchor: #BGBCFECBgrtop

Figure 2-4. Continuously Reinforced Concrete Pavement.

Anchor: #i1064778

Concrete Pavement Contraction Design (CPCD)

CPCD uses contraction joints to control cracking and does not use any reinforcing steel. An alternative designation used by the industry is jointed concrete pavement (JCP). Transverse joint spacing is selected such that temperature and moisture stresses do not produce intermediate cracking between joints. Nationally, this results in a spacing no longer than 20 ft. The standard spacing in Texas is 15.0 ft.

Dowel bars are typically used at transverse joints to assist in load transfer. Tie bars are typically used at longitudinal joints. Figure 2-5 shows a typical section of CPCD.

Concrete Pavement Contraction Design (CPCD). (click in image to see full-size image) Anchor: #BAGBDDJCgrtop

Figure 2-5. Concrete Pavement Contraction Design (CPCD).

Anchor: #i1064847

Jointed Reinforced Concrete Pavement (JRCP)

JRCP uses contraction joints and reinforcing steel to control cracking. Transverse joint spacing is longer than that for concrete pavement contraction design (CPCD) and, in Texas, it typically ranges from 30 ft. to 60 ft. This rigid pavement design option is no longer endorsed by the department because of past difficulties in selecting effective rehabilitation strategies. However, there are several remaining sections in service. Figure 2-6 shows a typical section of jointed reinforced concrete pavement.

Jointed Reinforced Concrete Pavement (JRCP). (click in image to see full-size image) Anchor: #BAGGAFDHgrtop

Figure 2-6. Jointed Reinforced Concrete Pavement (JRCP).

Anchor: #i1064950

Post-tensioned Concrete Pavements

Post-tensioned concrete pavements remain in the experimental stage and their design is primarily based on experience and engineering judgment. Post-tensioned concrete has been used more frequently for airport pavements than for highway pavements because the difference in thickness results in greater savings for airport pavements than for highway pavements.

Anchor: #i1064971

Composite Pavement

A composite pavement is composed of both hot mix asphalt (HMA) and hydraulic cement concrete. Typically, composite pavements are asphalt overlays on top of concrete pavements. The HMA overlay may have been placed as the final stage of initial construction, or as part of a rehabilitation or safety treatment. Composite pavement behavior under traffic loading is essentially the same as rigid pavement.

Anchor: #i1009122

Rigid and Flexible Pavement Characteristics

The primary structural difference between a rigid and flexible pavement is the manner in which each type of pavement distributes traffic loads over the subgrade. A rigid pavement has a very high stiffness and distributes loads over a relatively wide area of subgrade – a major portion of the structural capacity is contributed by the slab itself.

The load carrying capacity of a true flexible pavement is derived from the load-distributing characteristics of a layered system (Yoder and Witczak, 1975). Figure 2-7 shows load distribution for a typical flexible pavement and a typical rigid pavement.

Typical stress distribution under a rigid
and a flexible pavement. (click in image to see full-size image) Anchor: #BAGHHJICgrtop

Figure 2-7. Typical stress distribution under a rigid and a flexible pavement.


Previous page  Next page   Title page