Chapter 8: Temporary Lighting
Anchor: #i999118Section 1: Design and Layout
Anchor: #i999123Purpose
The purpose of temporary roadway lighting is to improve the ability of motorists to navigate the construction area.
Anchor: #i999133Difference Between Temporary and Work Zone Lighting
Temporary roadway lighting is not the same as work zone lighting. Work zone lighting is installed so that the contractor may work at night. If work zone lighting is installed, care should be taken to ensure that the visibility of passing motorists is not reduced below an acceptable level. Temporary roadway lighting helps reduce the negative effect of work zone lighting.
Anchor: #i999143Special Considerations
Some special considerations affecting the design of temporary lighting include:
- Anchor: #XWVDKBYG
- cost of system Anchor: #PPYJOSRM
- ease of installation Anchor: #GVGIJOGF
- ease of maintenance Anchor: #LMELDAEN
- ease of moving the temporary poles.
Because the purpose of temporary lighting is to make it safer to travel through the construction area, the lighting should be installed in such a way as to limit glare and avoid the placing of hazardous obstacles near the travel ways.
Roadway delineation should be considered along with any temporary lighting requirements.
Anchor: #i999183Types of Temporary Lighting
Some possible types of temporary lighting systems include:
- Anchor: #WPWWIGPF
- standard steel poles with or without breakaway bases Anchor: #IKXYBTMJ
- wood poles, 30- or 40-foot mounting height, protected from traffic, with standard highway light fixtures Anchor: #JSKTAIKX
- permanent high mast illumination installed early in project.
Illumination Levels
Illumination levels should be higher than normal, where practicable, in detour areas, gore areas, and other construction zone obstacles (impact attenuators, etc.).
Illumination levels and uniformity may be lower than normally required in areas where the motorist has no special navigational decisions to make.
Lighting systems should not create excessive glare, a potential problem with low mounting heights.
Anchor: #i999248Electrical System Integrity
Electrical safety and integrity must be maintained in temporary lighting. Follow these guidelines:
- Anchor: #JDNYSDLJ
- Where breakaway poles are used, breakaway electrical devices should also be used. Anchor: #INDDQHNE
- Overhead wiring may be considered where non-breakaway poles are used. Anchor: #BJDNDRVE
- Voltage should not exceed 277 VAC to ground for temporary lighting units mounted at 18 feet or less. Anchor: #DAKVUAXE
- It is sometimes cost effective to use permanent lighting service pole locations for the temporary system. Anchor: #QSKBVPOW
- Usually fused fixtures and non-fused breakaway disconnects are preferable for temporary lighting.
Placement of Light Poles
All poles located within the clear zone should be of the breakaway design or should be otherwise protected from vehicle impact (behind concrete barriers or guard rail). (See Chapter 6, Section 7, “Pole Placement Guidelines,” for more details.)
Anchor: #i999302Installation
When practical, temporary lighting should be installed before the existing lighting is disabled.
Anchor: #i999312Plans and Specifications
Temporary lighting plans should show:
- Anchor: #BDEDFPBR
- the type and number of units required Anchor: #WXGWLWQT
- locations, spacings, and offsets of poles Anchor: #SOQDYMGF
- bracket and pole details Anchor: #WGJVOWAC
- electrical connection details, such as:
- Anchor: #SNCHXVPK
- electrical services Anchor: #VPPSAAEC
- conduit and wire or cord runs Anchor: #UGHOMGQM
- strain pole connections and guys (if used) Anchor: #DYBGEHXL
- breakaway disconnects (if used).
Temporary lighting should be coordinated with traffic control plans, which should show where and when the poles are to be placed or relocated.
Specifications for fixtures, wiring, poles, and services should be included with the plans when non-standard items are used. Ensure that circuit voltage drop is compatible with the types of fixtures selected.